Issue

Vol. 26 No. 17 (2014): Vol 26 Issue 17

Copyright (c) 2014 AJC

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Micromorphology and Thermostability of PEEK/PEI/PES Plastics Alloys

https://doi.org/10.14233/ajchem.2014.18210
J.B. Chen
Department of Materials and Chemistry Engineering, Chizhou College, Chizhou, P.R. China
Z.Z. Li
Department of Materials and Chemistry Engineering, Chizhou College, Chizhou, P.R. China
X.H. Yang
Department of Materials and Chemistry Engineering, Chizhou College, Chizhou, P.R. China
J.M. Qian
Department of Materials and Chemistry Engineering, Chizhou College, Chizhou, P.R. China

Corresponding Author(s) : J.B. Chen

chjb8008@163.com

Asian Journal of Chemistry, Vol. 26 No. 17 (2014): Vol 26 Issue 17

Abstract

PEEK/PEI/PES plastics alloys were prepared by twin-screw extrusion molding. Microstructure analysis showed that poly(ether imide) (PEI) and poly(aryl ether sulfone) (PES) can be well-balanced dispersed in poly(ether ether ketone) (PEEK) matrix. The PEEK has better compatibility with PEI than that of PES and that PEI can improve the compatibility between PEEK and PES and that there is a certain interaction between three components. But there are some regions in alloys without interaction between PEEK and PEI when PES was increased. Thermostability of materials could not be affected by alloying and there is little influence on the stability of ternary alloys for the heat treatment process of thermal compression molding.

Keywords

Poly(ether ether ketone) Poly(ether imide) Poly(aryl ether sulfone) Plastics alloy Micromorphology Thermostability
Chen, J., Li, Z., Yang, X., & Qian, J. (2014). Micromorphology and Thermostability of PEEK/PEI/PES Plastics Alloys. Asian Journal of Chemistry, 26(17), 5800–5804. https://doi.org/10.14233/ajchem.2014.18210
Download Citation
Endnote/Zotero/Mendeley (RIS)
BibTeX
References
  1. K. Friedrich, Z. Zhang and A.K. Schlarb, Composite Sci. Technol., 65, 2329 (2005); doi:10.1016/j.compscitech.2005.05.028.
  2. A.A. Goodwin, J.N. Hay, G.A.C. Mouledous and F. Biddlestone, 5th Rolduc Polymer Meeting, Limburg, The Netherlands, pp. 44 (1990).
  3. G. Crevecoeur, Ph.D. Dissertation, Catholic University Louvain, Belgium, p. 63 (1990).
  4. M.J. Jenkins, Polymer, 41, 6803 (2000); doi:10.1016/S0032-3861(00)00033-1.
  5. B. Nandan, L.D. Kandpal and G.N. Mathur, J. Polym. Sci., B, Polym. Phys., 40, 1407 (2002); doi:10.1002/polb.10199.
  6. B. Nandan, L.D. Kandpal and G.N. Mathur, Polymer, 44, 1267 (2003); doi:10.1016/S0032-3861(02)00852-2.
  7. B. Nandan, L.D. Kandpal and G.N. Mathur, J. Appl. Polym. Sci., 90, 2906 (2003); doi:10.1002/app.13012.
  8. B. Nandan, L.D. Kandpal and G.N. Mathur, J. Appl. Polym. Sci., 90, 2887 (2003); doi:10.1002/app.13009.
  9. R. Androsch, H.J. Radusch, F. Zahradnik and M. Münstedt, Polymer, 38, 397 (1997); doi:10.1016/S0032-3861(96)00518-6.
  10. B. Nandan, L.D. Kandpal and G.N. Mathur, J. Polym. Sci., B, Polym. Phys., 42, 1548 (2004); doi:10.1002/polb.20039.
  11. M. Frigione, C. Naddeo and D. Acierno, Polym. Eng. Sci., 36, 2119 (1996); doi:10.1002/pen.10608.
  12. G. Crevecoeur and G. Groeninckx, Macromolecules, 24, 1190 (1991); doi:10.1021/ma00005a034.
  13. J.B. Chen, Q. Guo, Z. Zhao, X. Shao, X. Wang and C. Duan, J. Appl. Polym. Sci., 127, 2220 (2013); doi:10.1002/app.37923.
  14. L. Niu, W.J. Zhang, H.J. Lv and D.Z. Jiang, Chemical J. Chinese Univ., 16, 119 (1995).
  15. S. Wen, C.L. Gong, G.W. Zheng, Y. Zhou and R. Guan, Polym. Mater. Sci. Eng., 25, 85 (2009).
Read More
Author biographies is not available.
Download
PDF
Statistic
Read Counter : 0 Download : 0