Copyright (c) 2021 AJC
This work is licensed under a Creative Commons Attribution 4.0 International License.
Structurally Designed Imine Skeletal Pyrenyl Pendant Pyridine Core Polybenzoxazine nSiO2/PBZ Hybrid Polymer Nanocomposites
Corresponding Author(s) : S.G. Gunasekaran
Asian Journal of Chemistry,
Vol. 33 No. 4 (2021): Vol 33 Issue 4
Abstract
Novel polybenzoxazine-silica (nSiO2/PBZ) hybrid nanocomposites were designed and synthesized using carbazole terminal pyrenyl pyridine core imine skeletal benzoxazine monomer (PYCBZ) and nanosilica (nSiO2) through in situ sol-gel method. The FT-IR and Raman spectral studies ascertained the formation of nanosilica reinforced polybenzoxazine hybrid nanocomposites. The nSiO2/PBZ hybrid nanocomposites exhibited excellent thermal stability and higher char yield than that of neat PBZ. The elevation in glass transition temperature of the nanocomposites was evidenced by the limited motion of the polymeric network with the introduction of nanosilica particles in the PBZ matrices. The hydrophobic nature of a less polar nSiO2 in the composites zipped the water uptake behaviour of (nSiO2/PBZ) hybrid nanocomposites to low percentage. The shift in the absorption peak reveals that the nanosilica particles were successfully incorporated through thermal ring opening polymerization of benzoxazine. The homogeneous reinforcement of nSiO2 particles retains the fluorescent properties of polybenzoxazine. The uniform molecular level dispersion of nano SiO2 onto polybenzoxazine networks were confirmed from transmission electron microscope and scanning electron microscope images.
Keywords
Download Citation
Endnote/Zotero/Mendeley (RIS)BibTeX
- H. Zou, S. Wu and J. Shen, Chem. Rev., 108, 3893 (2008);https://doi.org/10.1021/cr068035q
- Y. Lin, J. Jin, M. Song, S.J. Shaw and C.A. Stone, Polymer (Guildf.), 52, 1716 (2011); https://doi.org/10.1016/j.polymer.2011.02.041
- S. Zhang, Y. Yan, X. Li, H. Fan, Q. Ran, Q. Fu and Y. Gu, Eur. Polym. J., 103, 124 (2018); https://doi.org/10.1016/j.eurpolymj.2018.03.013
- S.B. Shen and H. Ishida, J. Polym. Sci., B, Polym. Phys., 37, 3257 (1999); https://doi.org/10.1002/(SICI)1099-0488(19991201)37:23<3257::AID-POLB1>3.0.CO;2-0
- K.S. Santhosh Kumar, C.P. Reghunadhan Nair, R. Sadhana and K.N. Ninan, Eur. Polym. J., 43, 5084 (2007); https://doi.org/10.1016/j.eurpolymj.2007.09.012
- T. Lakshmikandhan, A. Chandramohan, K. Sethuraman and M. Alagar, Des. Monomers Polym., 19, 67 (2016); https://doi.org/10.1080/15685551.2015.1092014
- C.F. Wang, Y.T. Wang, P.H. Tung, S.W. Kuo, C.H. Lin, Y.C. Sheen and F.C. Chang, Langmuir, 22, 8289 (2006); https://doi.org/10.1021/la061480w
- H. Oie, A. Sudo and T. Endo, J. Polym. Sci. A Polym. Chem., 48, 5357 (2010); https://doi.org/10.1002/pola.24338
- Y. Jiang, S. Yan, Y. Chen and S. Li, J. Adhes. Sci. Technol., 33, 1974 (2019); https://doi.org/10.1080/01694243.2019.1623434
- H. Ishida and H.Y. Low, J. Appl. Polym. Sci., 69, 2559 (1998); https://doi.org/10.1002 (SICI)1097-4628(19980926)69:13<2559:: AID-APP5>3.0.CO;2-9
- T. Agag and T. Takeichi, Polymer, 52, 2757 (2011); https://doi.org/10.1016/j.polymer.2011.04.044
- C. Schramm, B. Rinderer, R. Tessadri and H. Duelli, J. Sol-Gel Sci. Technol., 53, 579 (2010); https://doi.org/10.1007/s10971-009-2135-7
- M. Selvi, S. Devaraju, M.R. Vengatesan and M. Alagar, J. Sol-Gel Sci. Technol., 72, 518 (2014); https://doi.org/10.1007/s10971-014-3467-5
- T. Agag and T. Takeichi, Polym. Compos., 29, 750 (2008); https://doi.org/10.1002/pc.20448
- M.R. Vengatesan, S. Devaraju, K. Dinakaran and M. Alagar, Polym. Compos., 32, 1701 (2011); https://doi.org/10.1002/pc.21177
- M. Selvi, M.R. Vengatesan, S. Devaraju, M. Kumar and M. Alagar, RSC Adv., 4, 8446 (2014); https://doi.org/10.1039/c3ra44511a
- S. Jothibasu, A.A. Kumar and M. Alagar, High Perform. Polym., 23, 11 (2011); https://doi.org/10.1177/0954008310389838
- R.P. Priya, S.G. Gunasekaran and M. Dharmendirakumar, J. Nanosci. Nanotechnol., 15, 9509 (2015); https://doi.org/10.1166/jnn.2015.10741
- S. Devaraju, M.R. Vengatesan, A.A. Kumar and M. Alagar, J. Sol-Gel Sci. Technol., 60, 33 (2011); https://doi.org/10.1007/s10971-011-2547-z
- V. Selvaraj, K.P. Jayanthi, T. Lakshmikandhan and M. Alagar, RSC Adv., 5, 48898 (2015); https://doi.org/10.1039/C5RA07480K
- K.S. Santhosh Kumar, C.P. Reghunadhan Nair and K.N. Ninan, Eur. Polym. J., 45, 494 (2009); https://doi.org/10.1016/j.eurpolymj.2008.11.001
- Y. Wang, K. Kou, Z. Li, G. Wu, Y. Zhang and A. Feng, High Perform.Polym., 28, 1235, (2016); https://doi.org/10.1177/0954008315623353
- H. Ardhyananta, M.H. Wahid, M. Sasaki, T. Agag, T. Kawauchi, H. Ismail and T. Takeichi, Polymer, 49, 4585 (2008); https://doi.org/10.1016/j.polymer.2008.08.030
- K. Adachi, A. Achimuthu and Y. Chujo, Macromolecules, 37, 9793 (2004); https://doi.org/10.1021/ma0400618
- T. Agag, H. Tsuchiya and T. Takeichi, Polymer, 45, 7903 (2004); https://doi.org/10.1016/j.polymer.2004.09.022
- S.G. Gunasekaran, V. Arivalagan, M. Dharmendirakumar and L.D. Stephen, J. Nanosci. Nanotechnol., 17, 5271 (2017); https://doi.org/10.1166/jnn.2017.13810
- S.G. Gunasekaran, K. Rajakumar and M. Dharmendirakumar, Polym. Plast. Technol. Eng., 54, 989 (2015); https://doi.org/10.1080/03602559.2014.974281
- S.G. Gunasekaran, K. Rajakumar, M. Dharmendirakumar and M. Alagar, Int. J. Plast. Technol., 19, 309 (2015); https://doi.org/10.1007/s12588-015-9111-6
- N. Amutha and M. Sarojadevi, J. Polym. Res., 15, 487 (2008); https://doi.org/10.1007/s10965-008-9193-3
- S.G. Gunasekaran, K. Rajakumar and M. Dharmendirakumar, Int. J. Nanosci., 14, 1550021 (2015); https://doi.org/10.1142/S0219581X15500210
- R. Hariharan, S. Bhuvana, M.A. Malbi and M. Sarojadevi, J. Appl. Polym. Sci., 93, 1846 (2004); https://doi.org/10.1002/app.20650
- S. Yan, W. Chen, X. Yang, C. Chen, M. Huang, Z. Xu, K.W.K. Yeung and C.F. Yi, Polym. Bull., 66, 1191 (2011); https://doi.org/10.1007/s00289-010-0343-5
- T. Agag and T. Takeichi, J. Polym. Sci. A Polym. Chem., 44, 1424 (2006); https://doi.org/10.1002/pola.21245
- T. Hanemann and D.V. Szabo, Materials, 3, 3468 (2010); https://doi.org/10.3390/ma3063468
- S.G. Gunasekaran, K. Rajakumar, M. Dharmendirakumar and M. Alagar, J. Polym. Res., 21, 342 (2014); https://doi.org/10.1007/s10965-013-0342-y
- D. Zhuo, A. Gu, G. Liang, J. Hu, L. Cao and L. Yuan, Polym. Degrad. Stab., 96, 505 (2011); https://doi.org/10.1016/j.polymdegradstab.2011.01.006
- R. Sasikumar, N. Padmanathan and M. Alagar, New J. Chem., 39, 3995 (2015); https://doi.org/10.1039/C4NJ02188F
- H. Ardhyananta, T. Kawauchi, T. Takeichi and H. Ismail, High Perform. Polym., 22, 609 (2010); https://doi.org/10.1177/0954008309354129
- T. Agag and T. Takeichi, Polymer (Guildf.), 41, 7083 (2000); https://doi.org/10.1016/S0032-3861(00)00064-1
- S. Devaraju, M.R. Vengatesan, M. Selvi, A.A. Kumar, I. Hamerton, J.S. Go and M. Alagar, RSC Adv., 3, 12915 (2013); https://doi.org/10.1039/c3ra41144c
- J. Narayanan, M.J. Jungman and D.L. Patton, React. Funct. Polym., 72, 799 (2012); https://doi.org/10.1016/j.reactfunctpolym.2012.07.012
- S. Devaraju, M.R. Vengatesan, M. Selvi, J.K. Song and M. Alagar, Polym. Compos., 34, 904 (2013); https://doi.org/10.1002/pc.22496
- T.P. Jung, A.S. Jin, H.A. Sung, H.K. Jong and W.K. Sang, J. Ind. Eng. Chem., 16, 517 (2010); https://doi.org/10.1016/j.jiec.2010.03.030
References
H. Zou, S. Wu and J. Shen, Chem. Rev., 108, 3893 (2008);https://doi.org/10.1021/cr068035q
Y. Lin, J. Jin, M. Song, S.J. Shaw and C.A. Stone, Polymer (Guildf.), 52, 1716 (2011); https://doi.org/10.1016/j.polymer.2011.02.041
S. Zhang, Y. Yan, X. Li, H. Fan, Q. Ran, Q. Fu and Y. Gu, Eur. Polym. J., 103, 124 (2018); https://doi.org/10.1016/j.eurpolymj.2018.03.013
S.B. Shen and H. Ishida, J. Polym. Sci., B, Polym. Phys., 37, 3257 (1999); https://doi.org/10.1002/(SICI)1099-0488(19991201)37:23<3257::AID-POLB1>3.0.CO;2-0
K.S. Santhosh Kumar, C.P. Reghunadhan Nair, R. Sadhana and K.N. Ninan, Eur. Polym. J., 43, 5084 (2007); https://doi.org/10.1016/j.eurpolymj.2007.09.012
T. Lakshmikandhan, A. Chandramohan, K. Sethuraman and M. Alagar, Des. Monomers Polym., 19, 67 (2016); https://doi.org/10.1080/15685551.2015.1092014
C.F. Wang, Y.T. Wang, P.H. Tung, S.W. Kuo, C.H. Lin, Y.C. Sheen and F.C. Chang, Langmuir, 22, 8289 (2006); https://doi.org/10.1021/la061480w
H. Oie, A. Sudo and T. Endo, J. Polym. Sci. A Polym. Chem., 48, 5357 (2010); https://doi.org/10.1002/pola.24338
Y. Jiang, S. Yan, Y. Chen and S. Li, J. Adhes. Sci. Technol., 33, 1974 (2019); https://doi.org/10.1080/01694243.2019.1623434
H. Ishida and H.Y. Low, J. Appl. Polym. Sci., 69, 2559 (1998); https://doi.org/10.1002 (SICI)1097-4628(19980926)69:13<2559:: AID-APP5>3.0.CO;2-9
T. Agag and T. Takeichi, Polymer, 52, 2757 (2011); https://doi.org/10.1016/j.polymer.2011.04.044
C. Schramm, B. Rinderer, R. Tessadri and H. Duelli, J. Sol-Gel Sci. Technol., 53, 579 (2010); https://doi.org/10.1007/s10971-009-2135-7
M. Selvi, S. Devaraju, M.R. Vengatesan and M. Alagar, J. Sol-Gel Sci. Technol., 72, 518 (2014); https://doi.org/10.1007/s10971-014-3467-5
T. Agag and T. Takeichi, Polym. Compos., 29, 750 (2008); https://doi.org/10.1002/pc.20448
M.R. Vengatesan, S. Devaraju, K. Dinakaran and M. Alagar, Polym. Compos., 32, 1701 (2011); https://doi.org/10.1002/pc.21177
M. Selvi, M.R. Vengatesan, S. Devaraju, M. Kumar and M. Alagar, RSC Adv., 4, 8446 (2014); https://doi.org/10.1039/c3ra44511a
S. Jothibasu, A.A. Kumar and M. Alagar, High Perform. Polym., 23, 11 (2011); https://doi.org/10.1177/0954008310389838
R.P. Priya, S.G. Gunasekaran and M. Dharmendirakumar, J. Nanosci. Nanotechnol., 15, 9509 (2015); https://doi.org/10.1166/jnn.2015.10741
S. Devaraju, M.R. Vengatesan, A.A. Kumar and M. Alagar, J. Sol-Gel Sci. Technol., 60, 33 (2011); https://doi.org/10.1007/s10971-011-2547-z
V. Selvaraj, K.P. Jayanthi, T. Lakshmikandhan and M. Alagar, RSC Adv., 5, 48898 (2015); https://doi.org/10.1039/C5RA07480K
K.S. Santhosh Kumar, C.P. Reghunadhan Nair and K.N. Ninan, Eur. Polym. J., 45, 494 (2009); https://doi.org/10.1016/j.eurpolymj.2008.11.001
Y. Wang, K. Kou, Z. Li, G. Wu, Y. Zhang and A. Feng, High Perform.Polym., 28, 1235, (2016); https://doi.org/10.1177/0954008315623353
H. Ardhyananta, M.H. Wahid, M. Sasaki, T. Agag, T. Kawauchi, H. Ismail and T. Takeichi, Polymer, 49, 4585 (2008); https://doi.org/10.1016/j.polymer.2008.08.030
K. Adachi, A. Achimuthu and Y. Chujo, Macromolecules, 37, 9793 (2004); https://doi.org/10.1021/ma0400618
T. Agag, H. Tsuchiya and T. Takeichi, Polymer, 45, 7903 (2004); https://doi.org/10.1016/j.polymer.2004.09.022
S.G. Gunasekaran, V. Arivalagan, M. Dharmendirakumar and L.D. Stephen, J. Nanosci. Nanotechnol., 17, 5271 (2017); https://doi.org/10.1166/jnn.2017.13810
S.G. Gunasekaran, K. Rajakumar and M. Dharmendirakumar, Polym. Plast. Technol. Eng., 54, 989 (2015); https://doi.org/10.1080/03602559.2014.974281
S.G. Gunasekaran, K. Rajakumar, M. Dharmendirakumar and M. Alagar, Int. J. Plast. Technol., 19, 309 (2015); https://doi.org/10.1007/s12588-015-9111-6
N. Amutha and M. Sarojadevi, J. Polym. Res., 15, 487 (2008); https://doi.org/10.1007/s10965-008-9193-3
S.G. Gunasekaran, K. Rajakumar and M. Dharmendirakumar, Int. J. Nanosci., 14, 1550021 (2015); https://doi.org/10.1142/S0219581X15500210
R. Hariharan, S. Bhuvana, M.A. Malbi and M. Sarojadevi, J. Appl. Polym. Sci., 93, 1846 (2004); https://doi.org/10.1002/app.20650
S. Yan, W. Chen, X. Yang, C. Chen, M. Huang, Z. Xu, K.W.K. Yeung and C.F. Yi, Polym. Bull., 66, 1191 (2011); https://doi.org/10.1007/s00289-010-0343-5
T. Agag and T. Takeichi, J. Polym. Sci. A Polym. Chem., 44, 1424 (2006); https://doi.org/10.1002/pola.21245
T. Hanemann and D.V. Szabo, Materials, 3, 3468 (2010); https://doi.org/10.3390/ma3063468
S.G. Gunasekaran, K. Rajakumar, M. Dharmendirakumar and M. Alagar, J. Polym. Res., 21, 342 (2014); https://doi.org/10.1007/s10965-013-0342-y
D. Zhuo, A. Gu, G. Liang, J. Hu, L. Cao and L. Yuan, Polym. Degrad. Stab., 96, 505 (2011); https://doi.org/10.1016/j.polymdegradstab.2011.01.006
R. Sasikumar, N. Padmanathan and M. Alagar, New J. Chem., 39, 3995 (2015); https://doi.org/10.1039/C4NJ02188F
H. Ardhyananta, T. Kawauchi, T. Takeichi and H. Ismail, High Perform. Polym., 22, 609 (2010); https://doi.org/10.1177/0954008309354129
T. Agag and T. Takeichi, Polymer (Guildf.), 41, 7083 (2000); https://doi.org/10.1016/S0032-3861(00)00064-1
S. Devaraju, M.R. Vengatesan, M. Selvi, A.A. Kumar, I. Hamerton, J.S. Go and M. Alagar, RSC Adv., 3, 12915 (2013); https://doi.org/10.1039/c3ra41144c
J. Narayanan, M.J. Jungman and D.L. Patton, React. Funct. Polym., 72, 799 (2012); https://doi.org/10.1016/j.reactfunctpolym.2012.07.012
S. Devaraju, M.R. Vengatesan, M. Selvi, J.K. Song and M. Alagar, Polym. Compos., 34, 904 (2013); https://doi.org/10.1002/pc.22496
T.P. Jung, A.S. Jin, H.A. Sung, H.K. Jong and W.K. Sang, J. Ind. Eng. Chem., 16, 517 (2010); https://doi.org/10.1016/j.jiec.2010.03.030